Nov 9 - 30: Free Lightburn Pro with every laser > $2,000* | 75-day Extended Returns
Nov 9-30: Free Lightburn Pro with every laser > $2,000*
Skip to content
OMTech Pronto 35 CO2 laser, which requires an external water chiller

Which Chiller Does Your OMTech Laser Need? CW-3000 vs CW-5000 vs CW-5200 by Model

Quick answer: Only the OMTech Maker and Pronto series need you to buy a separate chiller. The K40+ ships with a basic pump, the Polar Lite has a built-in water tank, the Polar 2 and Pro Quantum are air-cooled RF machines, and the Pro 2440 and Pro 3655 have the chiller built in. For Maker and Pronto, size the chiller to the tube: a CW-5000 covers most 60–100W machines, a CW-5200 suits 100–130W, and 150W machines run at the top of the CW-5200's range, so a larger unit is the safer choice for long jobs or hot shops. A CW-3000 is a passive cooler, not a true chiller, and it's only suitable for light-duty use on smaller tubes.

Table of Contents

Which OMTech Lasers Need a Chiller

Based on the calls our team fields every week, the chiller is the purchase most new OMTech owners don't realize they need until the machine is already on the way. Here's how cooling works across the current lineup:

OMTech series Tube Cooling out of the box Buy a chiller?
K40+ (45W) Glass External water pump, no reservoir Optional upgrade; strongly recommended for regular use
Polar Lite (55W) Glass Built-in water tank and pump No
Polar 2 (50W RF) RF Air-cooled No
Maker (60–150W) Glass Needs external cooling Yes
Pronto (60–150W) Glass External water chiller required, not included Yes
Pro 2440 / Pro 3655 / Pro 3655 Hybrid Glass Chiller built into the housing No
Pro Quantum (60W RF) RF Built-in air cooling No
Galvo, MOPA, Solis Duo Fiber Air-cooled No

If you'd rather not deal with a chiller at all, that's a real point in favor of the Polar Lite at the desktop tier, or the Pro series at the industrial tier. Our Pronto vs Pro comparison covers that tradeoff.

CW-3000 vs CW-5000 vs CW-5200: What's the Difference?

The CW model names come from TEYU (S&A), and most laser brands, including OMTech, sell chillers under the same CW numbering. The numbers matter because they describe two very different technologies.

CW-3000: a passive cooler, not a true chiller

The CW-3000 is a fan-cooled, thermolysis-type unit. It circulates water through a radiator and blows air across it. That means it can only bring the water down toward room temperature; it can't cool below ambient. TEYU positions it for light-duty CO2 machines up to about 80W. In a cool shop on short jobs, it works. In a hot garage in summer, or on long cutting runs, the water temperature keeps climbing.

CW-5000: the entry compressor chiller

The CW-5000 uses a refrigeration compressor, like a small fridge, so it can actively hold the water at a set temperature below room temperature. TEYU says it's commonly used with 60–100W glass tubes and lists it for glass tubes up to around 120W under suitable conditions.

CW-5200: more cooling capacity in the same footprint

The CW-5200 is also compressor-based, with substantially more cooling capacity than the CW-5000. TEYU lists it for glass tubes up to about 130W (or RF tubes up to about 60W), and its selection guide places 100–150W tubes in the CW-5200 band. OMTech's own FAQ notes that the CW-5202 is internally the same as the 5200 with double the inputs and outputs, for shops running two lasers or a two-tube laser off one chiller.

Bigger units: CW-5300 and up

For tubes beyond the CW-5200's range, TEYU's guidance steps up to the CW-5300 (glass tubes up to about 200W) and the CW-6000 series for 200W and above.

Model Cooling type Cools below room temp? Typical glass tube range (TEYU guidance)
CW-3000 Passive (fan and radiator) No Up to ~80W, light duty
CW-5000 Compressor Yes Commonly 60–100W, up to ~120W
CW-5200 / CW-5202 Compressor Yes Up to ~130W; listed for 100–150W in TEYU's selection guide
CW-5300 Compressor Yes Up to ~200W

TEYU's own pages give slightly different ranges for the same model, so treat these as bands rather than hard limits, and always check the cooling requirement in your machine's manual.

Chiller Sizing by OMTech Model

OMTech often names machines by tube rating and lists a higher peak figure in the title (the Maker MF2028-80, for example, is sold as a 90W machine). Size the chiller to the higher number, so you have margin rather than running at the edge.

OMTech machines Power Minimum Recommended for business use
K40+ 45W Included pump with a large water reservoir CW-3000
Maker MF1624-60, AF2028-60; Pronto 35 60W 60W CW-3000 (cool shop, short jobs) CW-5000
Maker MF2028-80, AF2028-80; Pronto 35 90W, Pronto 40 90W CW-5000 CW-5000; CW-5200 in hot shops
Maker MF2028-100; Pronto 35 100W, Pronto 45 100W CW-5000 CW-5200
Pronto 60 130W CW-5200 CW-5200; larger for long cutting runs
Maker AF4063-150; Pronto 75 150W CW-5200 CW-5300 class for heavy duty or hot shops

Two situations push you up a size: a warm room (garages and un-air-conditioned shops in summer) and long continuous jobs like cutting full sheets, where the tube is firing for an hour or more. Based on our experience selling laser engravers to universities, schools and businesses of all sizes, classrooms with short student jobs are the one setting where the minimum is usually fine.

Why Chiller Size Matters for Glass Tubes

A glass CO2 tube turns most of its input power into heat rather than laser light, and that heat has to go somewhere. When the water gets too warm, three things happen:

  • Output drops. A warm tube produces less laser power, so cuts that went through cleanly at the start of the day stop going through by mid-afternoon.
  • Results become inconsistent. Engraving depth and darkness drift as the water temperature changes during a job.
  • Tube life shortens. Running hot is one of the fastest ways to use up a glass tube's rated hours. OMTech rates the Polar Lite's glass tube at roughly 11,000 hours and the K40+ at around 3,500; poor cooling eats into that.

That's why an undersized chiller is false economy: the money saved on the chiller often goes into an early replacement tube. For more on how glass and RF tubes compare on lifespan, see our RF vs glass CO2 tube guide.

Setup: Temperature, Coolant and Placement

Water temperature

Owners commonly set compressor chillers to keep the water in the high teens to low 20s °C. One LightBurn forum user, for example, runs a CW-5000 at 18–20°C. Avoid setting it so cold that condensation forms on the tube in a humid room. Always follow the range in your machine's manual.

Coolant

Use distilled water, not tap water, which leaves mineral deposits. If the machine sits somewhere that can freeze, OMTech's own FAQ lists mixing propylene glycol (RV antifreeze) with distilled water at a 1:1 ratio. Don't use automotive antifreeze unless your manual approves it.

Placement and hookup

  • Leave clear space around the chiller's air intake and exhaust. A chiller pushed against a wall can't shed heat.
  • Connect the water lines in the direction your manual specifies and check for leaks before the first firing.
  • Wire the chiller's alarm or flow signal to the laser if your machine supports it, so the tube can't fire without coolant flowing.
  • Turn the chiller on before the laser, and leave it running for a few minutes after a long job.

Choose a CW-5000 If / Choose a CW-5200 If / Choose Bigger If

Choose a CW-5000 if:

  • You run a 60W or 80–90W Maker or Pronto
  • Your shop is climate-controlled and jobs are mostly engraving or short cuts

Choose a CW-5200 if:

  • You run a 100W or 130W machine
  • Your shop gets warm, or you run long cutting jobs on a 90W machine
  • You want headroom for a future upgrade; the CW-5202 also lets one unit serve two machines

Choose a CW-5300 class unit if:

  • You run a 150W Maker or Pronto for production cutting
  • Your machine runs most of the day in a room that isn't air-conditioned

Skip the chiller entirely if: you'd rather buy a Polar Lite, Polar 2, Pro or Pro Quantum, which all handle cooling internally. See our OMTech setup budget guide for how the chiller fits into total cost.

Frequently Asked Questions

Does the OMTech Pronto come with a chiller?

No. Every Pronto model uses a glass CO2 tube and needs an external water chiller, which isn't included. Budget for one when you buy the machine.

Do I need a chiller for an OMTech Maker?

Yes. The Maker series uses glass tubes that need external cooling. A CW-5000 suits most 60–90W Maker models, and a CW-5200 or larger suits the 100W and 150W models.

Which OMTech lasers don't need a chiller?

The Polar Lite (built-in water tank), the Polar 2 and Pro Quantum (air-cooled RF tubes), the Pro 2440, Pro 3655 and Pro 3655 Hybrid (chiller built in), and all of OMTech's fiber machines.

Is a CW-3000 good enough for a 60W CO2 laser?

For light hobby use in a cool room, it can be. Because it's a passive cooler that can't drop below room temperature, it struggles in warm shops and on long jobs. For business use on a 60W machine, a compressor chiller like the CW-5000 is the safer choice.

What's the difference between the CW-5200 and CW-5202?

According to OMTech's FAQ, the CW-5202 is internally the same as the CW-5200 but with double the inputs and outputs, so it can cool two lasers or a two-tube laser.

What size chiller do I need for a 100W CO2 laser?

A CW-5000 is the minimum; TEYU lists it for glass tubes up to about 120W. A CW-5200 gives you comfortable headroom, especially in a warm shop or on long cutting jobs.

What size chiller do I need for a 150W CO2 laser?

At least a CW-5200, which TEYU's selection guide places at 100–150W. Because 150W sits at the top of that band, a CW-5300 class unit is the safer choice for heavy production or hot rooms.

What coolant should I put in my laser chiller?

Distilled water. If there's any risk of freezing, OMTech's FAQ lists a 1:1 mix of propylene glycol (RV antifreeze) and distilled water.


For how every OMTech series compares, see our OMTech Laser Lineup guide, or browse the CO2 laser engravers collection.

Not sure which chiller fits your machine and shop? Contact The Maker's Chest — we'll help you size it before the laser arrives.

Written By

Alina Oprea profile picture

Alina Oprea

Maker & Equipment Specialist

Alina Oprea is a hands-on maker, jeweler, and workshop specialist at The Maker’s Chest, with 25 years of silversmithing experience alongside a background in woodworking, renovations, construction, and commercial ductwork installation.

Her experience spans decorative woodwork, hand-carved doors, jewelry fabrication, homebuilding with Habitat, and real jobsite problem-solving — giving her a practical understanding of materials, tools, workflow, and what machines need to deliver beyond the spec sheet.

Next article Laser Marking Spray on a CO2 Laser: How to Mark Metal Without a Fiber Laser
Skip the AI. Call an Expert. Skip the AI. Call an Expert.