xTool MetalFab Setup Guide: Power, Gas, Space and Safety Before It Arrives
Before an xTool MetalFab arrives, your shop needs four things in place: a 200–240V circuit sized for the welder, a cylinder of 99.99% argon or nitrogen with a regulator, floor space and fume extraction for the work area, and 1080 nm laser safety eyewear for everyone nearby. None of them are exotic, but each one can delay your first weld by a week if it's missed. This guide walks through each requirement using xTool's published specifications for the xTool MetalFab, so you can have the shop ready on delivery day.
Based on our experience selling laser welders to fabrication shops, schools and businesses of all sizes, electrical service is the step most often left until the machine is already on site. Start there.
Table of Contents
- Pre-Delivery Checklist
- Electrical Power: What Circuit Each Model Needs
- Shielding Gas: Argon, Nitrogen and Regulators
- Space, Weight and Environment
- Laser Safety: Eyewear, Work Area and Fire Risk
- Fume Extraction and Ventilation
- What to Budget Beyond the Machine
- Your First Day: Software, Presets and Fit-Up
- Frequently Asked Questions
Pre-Delivery Checklist
| Requirement | MetalFab 800W | MetalFab 1200W |
|---|---|---|
| Input voltage | 200–240V AC, 50/60 Hz | 200–240V AC, 50/60 Hz |
| Rated power / current | 3,000W, max 15A | 4,200W, max 21A |
| CNC Cutter power (if added) | 250W, 100–240V AC, max 2.5A | |
| Shielding gas | 99.99% argon or nitrogen, with regulator | |
| Cooling | Air-cooled (no water chiller needed) | |
| Welder size / weight | 24.9" × 12.0" × 18.6", 35 kg (77 lb) | 28.7" × 12.9" × 20.2", 38.2 kg (84 lb) |
| CNC Cutter size / weight | 46.3" × 45.6" × 48.4", 158 kg (348 lb) | |
| Operating temperature | -10°C to 40°C (14°F to 104°F) | |
| Laser class / eyewear | Class 4; laser safety eyewear rated for 1080 nm | |
| Fume handling | Duct outdoors or certified fume extraction | |
Electrical Power: What Circuit Each Model Needs
The MetalFab welder runs on 200–240V AC, not a standard 120V household outlet. xTool rates the 800W at 3,000W with a maximum draw of 15A, and the 1200W at 4,200W with a maximum draw of 21A. Those are the numbers to hand your electrician.
A dedicated circuit is the right setup for either model. Sharing a 240V line with a compressor, a MIG welder or a kiln risks nuisance trips in the middle of a weld, and a breaker that drops mid-seam means grinding out and redoing the joint. Your electrician will size the breaker, wire gauge and receptacle to your local code and to the plug supplied with your unit, so confirm the plug type when the machine ships rather than guessing ahead of time.
If you add the MetalFab CNC Cutter, it draws far less: 250W on 100–240V at a maximum of 2.5A. It doesn't need its own 240V circuit, but plan an outlet within reach of where the cutter bed will sit.
Choosing between models partly on power? An existing 240V welder circuit may already cover the 800W's 15A draw, while the 1200W's 21A draw is more likely to need a heavier circuit; your electrician can confirm either way. Our MetalFab 800W vs 1200W comparison covers the capability side, and how much power your laser welder actually needs covers the decision more broadly.
Shielding Gas: Argon, Nitrogen and Regulators
The MetalFab needs 99.99% argon or nitrogen while welding and cutting. Shielding gas protects the molten pool from oxygen, which is what keeps welds bright and free of porosity, and on the cutting side it clears molten metal from the kerf.
You'll need a cylinder, a regulator and a hose fitting from a local gas supplier. Most shops lease cylinders and pay per refill, so ask your supplier for pricing at your expected volume. xTool's SaveGas system cuts consumption by up to 50% compared with conventional setups, and xTool rates burr-free 4 mm stainless cuts at just 87 PSI, which helps keep refill costs down.
Which gas when? Argon is the common default for welding stainless and aluminum, while nitrogen is widely used for stainless and for clean cut edges. Our guide to laser welding shielding gas: argon, nitrogen and when to use each goes through the choice by material.
Space, Weight and Environment

The welder
The welder unit is compact for its class: 35 kg (800W) or 38.2 kg (1200W), small enough to sit on a cart beside the bench. The torch weighs about 550 g and connects through a cable, so position the unit where the cable reaches every part of your weld table without dragging across sharp stock.
The CNC Cutter
The cutter is the piece to plan around. At 46.3" × 45.6" × 48.4" and 158 kg (348 lb), it needs a clear floor area, a level surface and a delivery route with doors and turns wide enough for the crate. Its 24" × 24" bed has unlimited pass-through length, so leave clearance in front of and behind it if you'll feed long stock.
Environment
The MetalFab is air-cooled, so there's no water chiller to fill or maintain, and xTool rates it from -10°C to 40°C. An unheated garage in winter or a hot shop in summer are both within range. Keep the air intake clear of grinding dust, which is the main contaminant in a working fab shop.
Laser Safety: Eyewear, Work Area and Fire Risk
The MetalFab is a Class 4 laser product. It has 10 layered safety features, including contact-activated emission prevention that stops the laser firing unless the torch is touching the workpiece. That reduces the risk of accidental firing, but it doesn't remove the need for eye protection, because reflected light from a weld is still hazardous.
- Eyewear: laser safety glasses rated for 1080 nm are required for the operator and anyone nearby during operation. Ordinary welding shades and sunglasses are not rated for this wavelength.
- Work area: mark off the welding zone and keep visitors out of line of sight. Laser welding curtains rated for the wavelength help in a shared shop.
- Fire risk: welding and cutting throw sparks and hot spatter. Clear combustibles from the area, keep an extinguisher within reach and never leave a cut running unattended.
If the machine will be used in a school, a shared makerspace or a commercial space with employees, document a laser safety procedure before first use. Our guides to laser welding safety, PPE and fumes and designing a safe laser welding work cell cover what to put in place.
Fume Extraction and Ventilation
Laser welding and cutting produce metal fumes and fine particulates, especially on galvanized and coated steel. xTool's guidance is to duct fumes outdoors or use a certified fume extraction system, and never to run the machine in a closed room without extraction.
If ducting outside isn't practical, the SafetyPro Bundle pairs the welder and CNC Cutter with the SafetyPro AP2 Max air purifier, which captures weld and cut fumes at the source. Position any extraction inlet close to the work, because fumes disperse quickly once they leave the joint.
What to Budget Beyond the Machine
| Package | 800W | 1200W |
|---|---|---|
| Welder | $3,999 | $5,999 |
| Welder + CNC Cutter | $9,999 | $12,959 |
| SafetyPro Bundle (welder, cutter, AP2 Max) | $11,999 | $14,782 |
| CNC Cutter only (welder needed) | $6,999 | $6,999 |
Prices as of publish time, subject to change.
Beyond the package itself, set aside budget for the items that usually aren't on the order:
- Electrical work: a dedicated 240V circuit if you don't already have one. Book the electrician early, since scheduling often takes longer than the machine's delivery.
- Gas: cylinder lease or purchase, a regulator and refills from your local supplier.
- Eyewear: 1080 nm-rated laser safety glasses for every person in the work area.
- Extraction: ducting or a purifier if you don't choose the SafetyPro Bundle.
- Consumables: filler wire, nozzles and protective lenses wear with use, and xTool excludes consumables from the warranty.
- Bench and fixturing: a steel weld table and clamps. Good fit-up does more for weld quality than extra wattage.
For running costs and payback across laser welders generally, see how much a laser welder costs: 2026 prices, running costs and ROI.
Your First Day: Software, Presets and Fit-Up

Once power, gas and safety are in place, setup is quick. The 8-inch touchscreen ships with 108+ one-click material presets: choose the metal and thickness and the machine sets the parameters. The CNC Cutter runs from xTool's XCS software, with dual cameras for material recognition and nesting.
Start on scrap of the same alloy and thickness as your first real job. Clean the joint, clamp it tight and keep the gap small, because laser welding is far less forgiving of poor fit-up than MIG. Our guide to laser welding fit-up and gap tolerance explains why, and how to set up a laser welder covers routine maintenance once you're running.
Remember the MetalFab is built for metal only. It isn't designed for wood or acrylic, and xTool doesn't recommend it for engraving highly reflective metals like copper or silver.
Frequently Asked Questions
Can I plug the xTool MetalFab into a regular 120V outlet?
No. The MetalFab welder needs a 200–240V AC supply. The 800W draws up to 15A (3,000W) and the 1200W up to 21A (4,200W), so have a licensed electrician confirm or install a dedicated circuit before delivery. The optional CNC Cutter runs on 100–240V at up to 2.5A.
Does the MetalFab need a water chiller?
No. The MetalFab is air-cooled and rated to operate from -10°C to 40°C, so there's no chiller to buy, fill or maintain.
What shielding gas does the MetalFab use?
99.99% argon or nitrogen, supplied from a cylinder with a regulator. xTool's SaveGas system reduces consumption by up to 50% versus conventional setups. Running cost depends on your supplier and volume, so ask a local gas supplier for pricing.
Can I use the MetalFab in my garage?
Yes, if the garage has a suitable 240V circuit, ventilation and a controlled work area. The operating range of -10°C to 40°C covers most unheated garages. Duct fumes outdoors or use a fume extractor, keep combustibles away from sparks and make sure everyone nearby wears 1080 nm laser safety eyewear.
How much space does the MetalFab CNC Cutter need?
The cutter measures 1175 × 1157 × 1230 mm (46.3" × 45.6" × 48.4") and weighs 158 kg. Plan a level floor area with clearance at the front and back if you'll use its unlimited pass-through for long stock, and check the delivery route for the crate.
What safety equipment do I need for laser welding?
Laser safety eyewear rated for 1080 nm for the operator and everyone in the area, a controlled work zone, fume extraction and a fire extinguisher. The MetalFab is a Class 4 laser with contact-activated emission prevention, but reflected light is still hazardous without rated eyewear.
Do I need welding experience to set up the MetalFab?
No. The 108+ presets set parameters by material and thickness, and most first-time operators make usable welds within their first sessions. Clean material and tight fit-up still matter. Buying from The Maker's Chest also gives you a 75-day return window from the ship date and US-based support for setup questions.
Getting your shop ready for a MetalFab? Contact The Maker's Chest team with your electrical setup and the metals you work with, and we'll confirm what you need before the machine ships.