Nov 9 - 30: Free Lightburn Pro with every laser > $2,000* | 75-day Extended Returns
Nov 9-30: Free Lightburn Pro with every laser > $2,000*
Skip to content
OMTech Polar Lite 55W desktop CO2 laser used for laser marking spray on metal

Laser Marking Spray on a CO2 Laser: How to Mark Metal Without a Fiber Laser

Quick answer: Yes, a CO2 laser can mark bare stainless steel and other metals if you coat the surface with a laser marking spray first. CerMark, LaserBond and Enduramark are the common brands. Bare metal reflects the CO2 wavelength, so the laser can't mark it on its own. With a coat of spray, the beam fuses the coating onto the metal, and you rinse the rest off with water. It works well for occasional metal jobs on a machine you already own. If metal becomes a daily product line, a fiber laser is faster, cheaper per piece and needs no consumables.

Table of Contents

How Laser Marking Spray Works

A CO2 laser works at a wavelength that bare metal reflects instead of absorbing. As Epilog Laser explains in its metal marking guide, bare and uncoated metals bounce the CO2 beam off the surface, which is why direct metal marking normally calls for a fiber laser.

Marking spray gets around that. The spray leaves a thin layer of a ceramic- or glass-like compound on the metal. That coating does absorb CO2 energy. Where the laser hits, the coating heats up and bonds permanently to the metal surface, leaving a dark mark. Everywhere the laser didn't touch, the coating stays loose and washes off with water and a cloth.

The result is an additive mark: you're fusing a black layer onto the surface rather than removing or changing the metal itself, which is what a fiber laser does. That difference matters for durability, contrast and speed, and we'll come back to it below.

What CO2 lasers can mark without spray

You don't need spray for everything metallic. A CO2 laser can mark coated metals directly, because it's removing the coating rather than marking the metal underneath. That covers:

  • Powder-coated stainless tumblers and water bottles
  • Anodized aluminum (business cards, dog tags, flashlights)
  • Painted metal signs and enamel-coated items

Spray is for bare metal: polished or brushed stainless steel, chrome-plated items, brass, tools and data plates.

Which Marking Spray to Use

Three brands come up again and again in laser communities and manufacturer guides: CerMark, LaserBond and Enduramark. Laser manufacturers including Epilog and Trotec also publish guides around their own or partner sprays and pastes.

The most useful independent comparison we've seen is a test by Laguna Tools on a 40W CO2 laser, which ran several products on stainless steel, copper, aluminum and brass. In that test:

  • Stainless steel was the one metal every product could mark well.
  • LaserBond 100 was the standout across all four metals.
  • CerMark LMM6000 gave strong results on stainless and brass, but weaker results on copper and aluminum. CerMark LMM14 was also respectable.
  • Enduramark showed promise as a mid-priced alternative.
  • CRC Moly Lube, a dry lubricant not designed for laser marking, worked on stainless at slow speed and high power and was suggested as a cheap way for hobbyists to experiment.
Your situation Where to start
Mostly stainless tumblers, flasks and tags CerMark or LaserBond; both perform well on stainless
Mixed metals, including copper or aluminum LaserBond, based on the Laguna results
Just testing whether metal products will sell A small can of a mid-priced spray before you commit to the premium brands

Whichever brand you choose, buy it for the metals you actually sell, and run a test grid before you quote a customer job.

Which CO2 Lasers Can Use Marking Spray

Marking spray needs enough power to fuse the coating. Guides from All3DP put the floor at a CO2 laser of at least 30W, and xTool's spray instructions say over 25W. In practice, more power lets you run faster, which matters on longer jobs.

Every OMTech CO2 laser The Maker's Chest carries clears that bar:

OMTech machine Power Spray marking notes
K40+ 45W Works for flat tags and small plates; 8" × 12" bed and manual focus limit what fits
Polar Lite 55W Good all-round desktop option; autofocus helps keep the coating in focus
Polar 2 50W RF Finest detail on small text and logos thanks to the 0.07mm RF spot
Maker, Pronto, Pro 60–150W Most headroom for speed; the room for a rotary makes them the better fit for tumblers

For round items like tumblers and flasks, you'll also need a rotary. See our rotary attachment guide for roller vs chuck.

Step by Step: Marking Stainless Steel With a CO2 Laser

1. Clean the metal

Wipe the area with isopropyl alcohol and a lint-free cloth. Fingerprints and oil stop the coating from bonding evenly, and that shows up as patchy marks.

2. Apply a thin, even coat

Shake the can well and spray a light, even layer over the area you'll mark. Aim for full, uniform coverage rather than a thick layer; heavy coats tend to crack or flake and give inconsistent results. Some users apply liquid marking compounds with an airbrush for more control.

3. Let it dry completely

Follow the drying time on the can. Engraving a coating that's still wet gives weak, smeared marks and dirties your optics.

4. Focus on the coated surface

Set focus to the top of the coating, the same way you would for any surface. On round items, set focus at the point the laser will hit on the rotary.

5. Run a test grid first

Before the real job, mark a small grid of squares at different speed and power combinations on a scrap piece of the same metal. Pick the darkest, cleanest square. This one step saves the most wasted product.

6. Engrave, then rinse

Run the job, then rinse or wipe the excess coating off with water and a damp cloth, as both Epilog and Trotec recommend. The marked areas stay; the rest washes away. Inspect the mark and do a light scrub test before you ship it.

A safety note: always coat bare metal before you fire a CO2 laser at it. Owners on the LightBurn forum warn that firing a CO2 laser at bare, reflective stainless can bounce energy back toward the optics. Keep the lid closed and use the machine's normal fume extraction; the coating gives off fumes as it bonds.

Settings: Where to Start

Marking spray rewards high power and relatively slow speed, because the coating needs enough energy per spot to fuse to the metal. There's no universal setting, because results depend on the spray brand, your machine's wattage and optics, and the metal finish.

For a published reference point, Epilog's travel-mug guide uses 100% power, 30% speed and 500 DPI on a 60W Fusion Edge with CerMark Black. That's a starting point for a test grid on a machine of similar power, not a setting to copy blindly onto a different laser.

  • Too light or grey: slow down or add power. The coating didn't get enough energy to fully bond.
  • Mark washes off in places: the coat was uneven, still wet, or the surface wasn't clean.
  • Rough, bubbly edges: too much energy or too thick a coat. Speed up slightly or apply a thinner layer.

Save the winning settings as a material preset in LightBurn, labelled with the spray brand and metal, so you don't have to rediscover them next time.

Marking Spray vs Buying a Fiber Laser

Based on the calls our team fields every week, this is the real decision behind most marking-spray questions: can I keep doing metal on my CO2, or is it time for a fiber laser?

Factor CO2 + marking spray Fiber laser
Upfront cost A can of spray if you already own a CO2 A second machine; OMTech compact Galvo markers start around $1,700 at TMC as of publish time
Cost per piece Spray on every piece, plus cleaning time No consumable per mark
Steps per piece Clean, coat, dry, engrave, rinse Load and mark
Mark type Black layer fused on top Annealed, etched or deep-engraved into the metal
Color marking Black only Color on stainless and titanium with a MOPA source
Deep engraving No Yes
Best for Occasional metal orders on a CO2 you already own Metal as a regular product line

Based on our experience selling laser engravers to universities, schools and businesses of all sizes, the tipping point is usually volume rather than quality. A shop doing a few metal orders a month is well served by spray. Once metal tumblers, tags or tools become a weekly line, the coating and rinsing steps start eating real labor, and a fiber machine pays for itself in time saved. If you need color on metal, go straight to MOPA: see our OMTech Galvo vs MOPA guide. If you want metal and wood in one compact machine, the OMTech Solis Duo is the middle ground.

Choose Marking Spray If / Choose a Fiber Laser If

Choose marking spray if:

  • You already own a CO2 laser and metal is an occasional add-on, not your main product
  • You want to test demand for metal products before buying a second machine
  • Black marks on stainless, brass or tools are all your customers ask for

Choose a fiber laser if:

  • Metal is, or is about to be, a weekly product line
  • You want marks engraved into the metal rather than fused on top, or need deep engraving
  • You want color marking on stainless or titanium (MOPA)
  • Per-piece labor matters more than the upfront machine cost

Browse fiber laser engravers or the CO2 laser collection to compare options.

Frequently Asked Questions

Can a CO2 laser engrave stainless steel without marking spray?

Not bare stainless. The metal reflects the CO2 wavelength, so the beam doesn't mark it. A CO2 laser can mark powder-coated or painted stainless by removing the coating, but bare or polished stainless needs a marking spray or paste, or a fiber laser.

What is the best laser marking spray for a CO2 laser?

CerMark and LaserBond are the most widely used. In an independent test by Laguna Tools on a 40W CO2 laser, LaserBond 100 gave the best results across stainless, brass, copper and aluminum, while CerMark LMM6000 was strong on stainless and brass. For stainless-only work, either is a solid choice.

How many watts do I need to use laser marking spray?

Guides typically cite at least 25–30W of CO2 power. Every OMTech CO2 laser we carry, from the 45W K40+ up, meets that. More power lets you run faster.

Is a marking spray mark permanent?

Yes. When it's done properly, the coating bonds to the metal and survives washing. A weak or patchy mark that scrubs off usually means the coat was uneven, still wet, or the speed was too high.

Can I use marking spray on tumblers?

Yes, on bare stainless tumblers, using a rotary. Powder-coated tumblers don't need spray at all; the CO2 laser removes the powder coat directly to reveal the steel underneath.

Does marking spray work on aluminum and copper?

Results vary more than on stainless. In Laguna's test, some sprays struggled on copper and aluminum while LaserBond 100 performed well. Anodized aluminum doesn't need spray at all.

Is it cheaper to use marking spray or buy a fiber laser?

For occasional metal jobs, spray is far cheaper because you're using a machine you already own. For regular metal production, a fiber laser usually wins on total cost, because there's no consumable per piece and no coating or rinsing step.


For the full OMTech CO2 and fiber lineup, see our OMTech Laser Lineup guide.

Deciding whether to keep marking metal on your CO2 or add a fiber laser? Contact The Maker's Chest — we'll help you work out which makes sense for your volume.

Written By

Alina Oprea profile picture

Alina Oprea

Maker & Equipment Specialist

Alina Oprea is a hands-on maker, jeweler, and workshop specialist at The Maker’s Chest, with 25 years of silversmithing experience alongside a background in woodworking, renovations, construction, and commercial ductwork installation.

Her experience spans decorative woodwork, hand-carved doors, jewelry fabrication, homebuilding with Habitat, and real jobsite problem-solving — giving her a practical understanding of materials, tools, workflow, and what machines need to deliver beyond the spec sheet.

Previous article Which Chiller Does Your OMTech Laser Need? CW-3000 vs CW-5000 vs CW-5200 by Model
Next article Laser Engraver Rotary Attachment Guide: Roller vs Chuck, Setup, Settings and What You Can Engrave
Skip the AI. Call an Expert. Skip the AI. Call an Expert.